Interior latex paint construction process Interior latex paint construction considerations
Interior wall latex paint is one of the main decorative materials for interior walls and ceilings. It is characterized by good decorative effect, convenient construction, low environmental pollution, low cost, and extremely wide application. The following Xiaobian brings you the internal wall latex paint construction process and interior wall latex paint construction considerations in detail, I hope to help you! Interior wall latex paint construction process Operating conditions: 1. The moisture content of the base layer of the wall is not more than 10%. 2. Plastering operations are all completed. Pipes, openings, yin and yang angles, etc. should be plastered and trimmed in advance, and fully dried. 3. The installation of the door and window glass is completed, the construction of the wet work floor is completed, and the pressure test of the pipeline equipment is completed. 4, winter requirements under the heating conditions, the ambient temperature of not less than 5 °C. Operation process: 1. Process Flow: Clean up the wall surface → Repair the wall surface → Puttying → Brush the first time Latex paint → Brush the second time Latex paint → Brush The third time latex paint. 2. Clean the wall surface: Remove the wall from the skin and the loose part, and make up with the cement mortar, clean the remaining ash, and then sweep the wall. 3, repair the wall surface: with water gypsum will hit the wall and potholes and other gaps and other leveling, after drying with sandpaper protruding wear off, sweep the dust. 4, scraping putty: The number of scraping putty can be determined by the level of the wall surface, the general situation is three times, kitchen, toilet, bathroom with polyvinyl acetate emulsion: cement: water = 1:5:1 water-resistant putty. The first pass is covered with a rubber scraper horizontally. A scraper is followed by a scraper. The joint must not be left open. The final end of each scraper must be clean. After drying, sandpaper is used to polish the puffer and spots, and then clean the walls. The second time, the rubber scraper was used to scrape vertically, and the materials and methods used were the same with the first time putty. After drying, the sandpaper was smoothed and cleaned. The third time, use a rubber scraper to make up the putty or scrape the scraper with a steel scraper. Scrape the wall, dry it, and grind it with fine sandpaper. Do not leave or put on the putty. 5, brush the first pass of latex paint: Brushing sequence is the first brush after brushing the top wall, the wall is first up and down. Clean the wall first and wipe off the wall dust with a cloth. Latex paint is brushed with a row of pens. When a new row of pens is used, the floating hairs on the row pens and loose wools are removed. Stir the latex paint before use, dilute it with water, and prevent the paint from brushing off. After the dry putty putty, and then dried and polished with sandpaper, clean. 6, brush the second pass latex paint: operation requirements with the first pass, before using fully stirred, if not very thick, should not add water to prevent the bottom. After the film is dry, use a fine sandpaper to remove the wall lining and the row of pens, clean it and clean it. 7, brush the third pass of latex paint: practice with the second pass of latex paint. Because the latex paint film dries quickly, it should be operated quickly and continuously. When brushing, it starts from one end and gradually brushes to the other end. It is necessary to connect the brush up and down, and the rear row of pens immediately follows the previous row of pens to avoid the occurrence of joints after drying. Interior wall latex paint construction matters needing attention 1. Dilution methods, construction temperatures, and methods of use for various paints, etc. 2. Strictly implement the rules of use. 3. The paint required for a project should be the same batch of products and be prepared at one time. 4, the paint should be often stirred before use and use. 5, paint storage and transportation should be carried out in accordance with the instructions. 6, spray paint to avoid filming before filming. The above discussion on interior latex paint construction process and internal wall latex paint construction is briefly introduced here, and I hope to help you. For more information, please visit this website. Stay tuned. Latex paint Zhejiang Botuolini Machinery Co.,Ltd , https://www.chinaplungerpump.com