Many people will use ceiling lamps when decorating their new homes. Beautiful ceiling lamps can not only bring beautiful enjoyment to the people, but also it is affordable and can save a lot of decoration costs for everyone. The ceiling lamp is required to be installed before it can be used. This involves an installation problem. What are the installation methods of ceiling lamps? What are the precautions for installing ceiling lamps? The following Xiao Bian will share with you on these issues and look forward to helping those in need.

What are the installation methods of ceiling lamps?

Under normal circumstances, everyone will ask an electrician to help install the lights. In fact, the installation of ceiling lamps is not so difficult. Everyone can master the methods through learning. Before installation, everyone needs to remove the mask of the ceiling lamp and remove the lamp inside the lampshade to prevent the mask or the lamp tube from being accidentally broken during installation. If you are installing the lamp with wooden ceilings, plasterboards, etc., which are not very hard and the self-tapping screws can be screwed in, the installation procedure of the ceiling lamps is as follows:

1. Place the reserved wire in the wire hole that penetrates the base.

2. Hold the base of the lamp with one hand and press it in the desired position.

3. Use a screwdriver to screw in one of the holes, but do not twist it.

4. After fixing a screw, check the installation position again and adjust it properly.

5. After fixing, please screw the remaining screws.

6. Finally, connect the power cord to the lamp socket.

7. Install the lamp and mask.

What are the two ceiling lamp installation methods?

The way to decorate the top of each home is different, so there are some differences in the way ceiling lights are installed. If your home is topped with concrete or a harder material, you cannot use the above method. Because the self-tapping screws cannot be screwed in at all, you need to install the expansion screws. The ceiling lamp installation steps are as follows:

1. First select the position to be installed, and press the chassis by hand to press it on the wall.

2. Then use a pencil to insert the screw hole and draw the position of the screw.

3. Put the pedestal aside and use a hand drill (impact drill) to make a hole in the location marked by the pencil. Do not make the hole in the luminaire too large. Generally, a drill of No. 6 is enough.

4. After the hole is well-formed, press the plastic expansion tube into the hole. The wooden wedge cannot be used because the wooden wedge is too unstable and it is easy to rot for a long time.

5. Then pass the reserved wire through the wire hole and place the base in the previous position with the screw hole facing up. Use a screwdriver to screw the screw into the cork or plastic expansion tube.

6. Finally, install the lamp and mask.

What are the precautions for installing ceiling lamps?

In addition to mastering the installation method of ceiling lamps, we must also pay attention to certain matters so as to ensure the safety of personnel. Specific attentions are as follows:

1. Everyone should check whether the power supply in the home is turned off before installing the light, or if the wire needed to be installed is not available! Otherwise there is a safe life! The best advice is to ask a professional electrician to install it for you!

2. The two wire ends connected to the ceiling lamp power supply should have good electrical contact. They should also be wrapped with black tape and keep a certain distance. If possible, do not place the two wires under the same metal sheet. To avoid short circuit, danger.

3. If the lamp used in the ceiling lamp is a screw base, its wiring should also pay attention to the following two points: 1 phase line should be connected to the terminal on the center contact, the neutral line should be connected to the threaded terminal; 2 lamp cap insulation The housing should not be damaged or leaked to prevent electric shock when replacing the lamp.

4. We must not install ceiling lamps on flammable objects. Some families lining behind the ceiling lamps in order to use beautifully painted plywood. In fact, this is very dangerous and we must take thermal insulation measures; When approaching flammables, heat insulation or cooling measures must also be taken.

The above is about the ceiling lamp installation methods and the ceiling lamp installation precautions which are related to share, for everyone to be a reference! If you have more related issues, welcome to continue to pay attention to this site, and later will bring more exciting content for everyone.

Freestanding Bathtub Faucet

Floor Mounted Tub Filler with Hand Shower with 360 Degree Swivel.The hoses come with a nylon-braided exterior that protects against chemical corrosion (commonly caused by detergent) and rusting. Easy operation single handle design allows flow rate and temperature control in single hand. Handheld Shower head and high arch 360 degree swivel bath tub faucet change in one second through diverting valve knob.

Freestanding Bathtub Faucet,Bathroom Tub Faucets,Freestanding Bath Taps,Freestanding Bathtub Faucets

HESHAN CAIZUN SANITRAYWARE CO.,LTD , https://www.caizunsanitaryware.com