Top Ten Tips for Identifying Furniture
Furniture is closely related to people's lives, affecting people's quality of life and physical health. Therefore, before you buy furniture, it is best to make a good knowledge reserve in advance and learn some tips for identifying and identifying various furniture. Tuen Mun 1 Check if the fitting is properly installed For example, check that the door lock switch is not working; the big cabinet should be equipped with three dark hinges, and some can only be installed with two; the upper three screws, some cut corners, only one screw, will be used. Tuen Mun 2 mirror furniture to check the back Choose furniture with mirrors, such as dressing table, mirror, and dressing mirror. Take care of it and see if the mirror is deformed. Check if there is lining paper and backboard at the mercury in the back of the mirror. Qualified, no paper, no, otherwise the mercury will be worn away. Tuen Mun 3 sofa, soft bed to try When picking up sofas and soft beds, you should pay attention to the surface to be flat, but not high and low; soft and hard to be even, but not hard, that piece of soft; moderate hardness, neither too hard nor too soft. The method of selection is to sit down and squat with your hand, the flatness is not flat, and the spring does not ring. If the spring laying is unreasonable, causing the spring to bite the spring, it will make a sound. Secondly, it should also pay attention to whether the quilting has broken wires or jumpers, and whether the density of the corner teeth is reasonable. Tuen Mun 4 Check the veneer furniture is not strict Whether it is veneer veneer, PVC or pre-painted paper, it is necessary to pay attention to whether the leather is flat, whether there is drum, foaming or not. Look at the light when you check it, and don't see it when you don't. Ash veneer veneer veneer furniture is relatively easy to damage, generally only two years. In the case of wood veneers, the veneered veneers are better than the chopped ones. The way to identify the two is to look at the pattern of the wood. The wood texture of the cut veneer is straight and dense, and the veneered veneer pattern is curved and sparse. Particleboard veneer furniture, the ground part must be edged, and the edge banding will absorb moisture, rise and damage. Generally, the corners of the veneer furniture are easy to be tilted up. When picking, you can use your hand to rub the corners. If you get up, you will have problems with the glue. Tuen Mun 5 Various materials and furniture The texture and texture of the material determine the look and feel of the product. Wood is a natural material with natural and beautiful texture, vivid image, good hand feeling, easy to process and color, and is the best material for producing furniture. Plastics and their synthetic materials have the characteristics of simulating the texture of various natural materials, and have good coloring properties, but they are prone to aging and are susceptible to thermal deformation. With this, furniture is produced, and its service life and scope of use are limited. Tuen Mun 6 pay attention to the moisture content of wooden furniture The moisture content of furniture should not exceed 12%, the water content is high, and the wood is easy to warp and deform. When the average consumer buys, there is no test instrument. You can take the method of hand touch and touch the bottom of the furniture or the place where there is no paint inside. If you feel the moisture, the moisture content is at least 50%, which cannot be used at all. Another way is to sprinkle a little water on the unpainted wood. If it is slow or not, it indicates a high moisture content. Tuen Mun 7 Check if the furniture materials are reasonable Different furniture, surface materials are different. Such as tables, chairs, cabinet legs, the use of hardwood, relatively strong, can bear the weight, while the internal materials can be used other materials; the thickness of the large wardrobe legs to 2.5 cm, too thick is clumsy, thin and easy to bend Deformation; kitchen and bathroom cabinets can not be made of fiberboard, but should be used with plywood, because the fiberboard will expand and damage when exposed to water; the dining table should be washable. Tuen Mun 8 Children's Furniture Multiple Combination Because children grow faster, parents should not buy fixed or expensive sets of furniture, should use multi-functional or combination furniture; adjustable furniture can be used from childhood to adolescence, such as lifting bed, can be raised when you are young, you can put it when you are older Down; other furniture is best not to wear glass or mirror, so as not to break the wounded. Tuen Mun 9 balcony furniture focuses on material selection Wooden balcony furniture is the first choice, but wood with a higher oil content, such as teak, should be used to minimize the brittleness of the wood due to swelling or looseness. People who like metal materials should use aluminum or painted and waterproof alloyed balcony furniture, which is the most resistant to outdoor wind and rain. Bamboo and rattan furniture is easy to write, but pay attention to its maintenance, wipe it in time after rain. Tuen Mun 10 small-sized furniture refinement is not big Small-sized furniture is not suitable for complete purchase. It is best to fully consider the inclusiveness and performance integration of large and small furniture, and mix and match the perfect effect. Some simple, light and compact furniture, as well as furniture that can be combined, stored and moved at will, are easy to transport, easy to disassemble, and easy to arrange. This not only saves space, but also adds to the function of the room, and is rich in modernity. When you change the furniture in the future, you don't have to worry about it. Centering Spot Drill Solid Carbide
Carbide Spot Drill, It is mainly to make small holes in advance at the position where drilling is needed to facilitate positioning during drilling. which can be used for drilling non-ferrous metals (aluminum alloy, copper), cast iron, alloy steel, low carbon steel, high hard steel, stainless steel, And various difficult-to-process materials, etc.;
Centering Spot Drill Solid Carbide ,Solid Carbide Step Drills,Spot Drill Bit,Center Drill For Lathe ROYI CNC TOOL TAIXING CITY CO.,LTD , https://www.royitools.com