Everyone knows that the bathroom is a space where odors are likely to occur. If you do not care, you will feel heavy odors. Some odors are caused by lack of hygiene in your own home, and some odors come up inexplicably. Although the wooden floor is booming in the past two years, ceramic tiles are still indispensable in home decoration, especially in functional spaces such as the living room and restaurants. Most people still choose to install floor tiles and wall tiles. However, the hollowing of the tiles is very annoying.

If there is an empty drum tile, it will easily loosen, fall off, crack, etc., and it will also have potential safety hazards. If you drill a hole in an empty drum, this tile is also very easy to break.

Zhang Jian, manager of an entity's home improvement department, believes that kitchens, especially kitchen floors, cannot be empty. He said of such an example: "A friend who has a bathroom at home has a bad smell even if he cleans it up. After checking the toilet, he checked the floor drain and the sewer. There was no problem. Later I went to see if I saw it. A brick has empty drums, because kitchen and toilet floors often come into contact with water, and water penetrates through the brick seams and accumulates under the bricks.Since the tiles have been waterproofed under the tiles, the water will accumulate under the bricks for a long time. Dead water and finally odor. This is one of the reasons why there are always odors in many bathrooms and kitchens."

Priming plaster is not standard. Before the tile is applied, the wall base debris and dust must be removed. When laying, the back of the tile should be filled with cement mortar or 107 grout. Tap the tile with a hammer handle or a soft hammer to make the grout filled with the back of the tile. Press firmly to firmly bond the tiles to the wall base. If the base plaster is not standard, it will cause hollowing.

Soaking is not enough before laying. Tiles (especially glazed tiles) should be soaked in water for 2 hours or more before the tiles are applied. After the tiles are fully absorbed, remove the shade or clean the water. If the bricks are not saturated with water, the moisture in the mortar will be absorbed prematurely, resulting in hollowing of the mortar and affecting the adhesive strength.

The mortar is not full when applied. The tiles are not full or tiled and tapped to compact. This situation may be cutting corners, in order to save cement mortar, or to save time and sloppy.

Hollow detection method is actually very simple, find a metal item (the best tool is drill bit or key drill on the site, small stainless steel spoon can also), use it to hit the four corners and core parts of the tile. If there are more than two points emitting an "empty" sound, then this piece of tile has been mislaid. But it is important to note that the kitchen flue and the tiles on the walls that are covered with cement boards cannot be used for this type of inspection because the walls themselves are not solid, so how to knock is also the sound of empty drums.

If the walls of the tile wall are cracked or peeled off, the impact on the home environment can be imagined. So how to remedy the problem of empty tiles? Qin Ji'an suggested that if there is a large area emptying, all the bricks can be sucked up and re-paved by glass suction cups. After the hair is found on the ground cement layer, the base layer is re-founded and the tiles are then tiled.

If the owner’s home still retains the remaining tiles after the renovation, you can replace all the problem bricks directly. Tiles on the market are currently being updated very quickly. It also reminds owners who are renovating that they should buy some of the main materials, such as tiles, for use in later maintenance.

To prevent emptying and shedding, the wall base must be cleaned and all kinds of dirt on the wall should be thoroughly cleaned. Before the tiles are used, they must be cleaned. Soak the tiles with clean water until they do not bubble. Then remove the tiles and wait for the surface to dry before spreading. If necessary, 108% cement with a weight of 3% to 5% can be added to the cement mortar to increase the adhesion force.

If there is a crack in the wall itself when pasting, it should be properly treated before it can be tiled to prevent the cracking or shedding of the tile after the basic structural cracks become larger in the future; also, for floors and walls where the gap between flatness and verticality is too large, Also use cement mortar for leveling treatment.

Summary: After reading this article, everyone also learned a lot of relevant knowledge. The reasons for bathroom odor are also mentioned in the article. If the odor is not done properly, we must pay attention to it. A bright and clean bathroom. If the odor is caused by the reason of the floor tiles, you must solve the problem from the source. Prevent odors from happening again.

Decoration Experience Bathroom Decor Tile Laminate Cement Glass Home Furnishing Decoration Toilet Glass Tile Kitchen Wall Tile Kitchen Glass Sliding Door Bathroom Waterproof Bathroom Wall Tile Bathroom Tile Tile Plastic Kitchen Tile Decoration Home LD Tile

Customized Extruded Profile

Customized Extruded Profile,Pvc Extruded Profile,Pvc Extrusion Profile,Extrusion Pvc Profile

Wuxi Jierui Changkun New Material Technology Co., Ltd , https://www.jrck-plastic.com