Thread milling and tapping threads save machining and tool change time
From the perspective of process safety, thread milling is a superior tapping technique. The M6 ​​thread milling head with 240mm tool flanges allows for over 5000h service life with external drill teeth (only half the number of teeth). Manufacturers can find professional companies to cooperate in further reducing production cycle time, improving component production process safety, improving independent research and development of motor products, and cutting. For example, Komet chose to use standard or special tools such as Komet, Dihart and Jel for more demanding inside machining and machining operations from boring to threading. With a threaded milling head, the required drill holes can be made directly on the housing cover. The processing of the lateral channel air compressor casing is particularly challenging. The complex shape of the housing cover has many disturbing profiles, increasing the difficulty of machining and forcing the flange of the threaded tool to lengthen. Only shaft extensions can be used for this. If the standard tapping milling head is M62.5D, the tool flange reaches 240mm. Long flanges can cause large radial forces. The result of machining in this way is that after machining 50 to 60 threads, The tool may break. The reason is that the flange is too long and the radial force acting on the tool is relatively large. The use of tapping milling is the best choice. This process saves a single piece of tool and delivers significant time savings. In addition, this technology can also be applied to modern machining centers. Despite the difficulty in grasping the tool breakage during tapping milling, the required reliability is not achieved, but because of the significant advantages of this process, even if the tool breaks, a positive view is drawn that The tools are not left in the borehole, so there is no need to spend time cleaning the holes and no defective products. Another advantage of tapping milling technology is that it allows for drilling, reaming and tapping in one process. When tapping with the traditional technology, two or three kinds of tools (such as auger, reaming or trapezoidal and thread drill) are required. When the thread milling process is used, the tool consumption can be saved and the tool change time can be saved. . The number of teeth is halved but the safety is enhanced. From the point of view of operational safety, in order to supply fresh air when tapping the casing of the lateral passage air compressor, it is a better choice to adopt an external drilling method. Since the number of teeth is reduced by half compared to the original process, it is necessary to reduce the feed rate and increase the machining time. However, this effect is not significant relative to the operational safety achieved. As a result, the tool life can reach 5000 to 5200 threads at once. Due to the use of external drill teeth, the radial force of the tool is also greatly reduced. In order to achieve the best use of the tapping milling head in the machining center, the TCT online CNC program software was used. In this way, Komet has also achieved the selection of the most suitable threading tools and the development of machining procedures for various occasions. The programmed procedure ensures 100% dimensional accuracy and optimum feed rate and cutting speed.
500nm led is a green LED. Common aqua blue LEDs are like: green 500nm LED, green 505nm LED, green 510nm led and so on.
We
supply variety of 500nm LED products. Including Through-hole 500nm LED,
SMD 500nm LED and high-power 500nm LED. We can also produce 500nm LED
according to your requirement.
For the Through-hole Light Emitting Diode 500nm traffic green LED,
we
can customize the shape, the lighting angle, the number of emitting
source, the flat pin LED and braided LED. Such as: 5mm traffic green 500nm LED,
5mm traffic green 505nm LED, 5mm traffic green 510nm LED. 3mm traffic green 500nm LED, 3mm traffic green 505nm LED, 3mm traffic green 510nm LED ect.
There are many other shapes for your choose. Customized cyan LED are available
For the SMD LED 500nm LED,
we
can supply dual-chip blue LED, three-chip cyan LED, multi-chip cyan LED, high voltage LED, flashing cyan LED and variety of size
SMD LED. For instance: 3528 SMD traffic green 500nm LED, 3528 SMD traffic green 505nm
LED, 3528 SMD traffic green 510nm LED.
2835 SMD traffic green 500nm LED, 2835 SMD traffic green 505nm LED, 2835 SMD traffic green 510nm LED.
There are also have many other shapes to choose, like the
5050 SMD green LED, the 5730 SMD green LED ect. You can choose any one
of them for your requirement.
500Nm LED,500Nm LED,CE Certified 500Nm LED,3W 500Nm LED Shenzhen Best LED Opto-electronic Co.,Ltd / BESTSMD CO LIMITED(HK) , https://www.bestsmd.com
We are 500nm LED manufacturer from China.