Stainless steel gear pump construction features

September 18 21:00:11, 2024

Stainless steel gear pump, also known as sanitation pump, is mainly used in food industry. Stainless steel gear pump is a horizontal rotary pump, the main pump, gears, housings, safety valves, bearings and seals and other mechanical parts group. Stainless steel gear pump equipped with safety valve, when the gear pump or discharge pipe failure or mistakenly discharge valve is completely closed to produce high pressure and high pressure impact valve will be from the pump, bearing and so on for the gray iron, gear with high-quality carbon Su steel production, but also according to the special needs of users with copper or stainless steel material made of the bearing seat on the packing box, played the role of axial seal. KCB series gear pump with mechanical density device, the bearings using single row radial ball bearings. KCB-18.3 ~ 83.3-type pump with three oil-resistant rubber ring and the middle of a spacer ring composed of adjusting pressure on the cover of the two nuts to adjust the degree of sealing, bearings using copper-based powder oil bearing. In addition, stainless steel gear pumps can be filled with packing to good flexibility, high temperature and low temperature, chemical stability and self-lubricating flexible graphite as a filler. Open or remove some or all of the high-pressure liquid back to the low-pressure chamber, thus gear pump and pipe play a safety role. Elastic coupling with the drive motor directly connected and mounted on a common cast iron chassis.
Solar Mounting System For Green House
The Installation of Mounting Unit
1. Make the concrete base according to solution drawing, locate embedded bolts and set out strings by Laser Level to ensure the centers of embedded bolts in the same elevation as accurate as possible on vertical, horizontal direction and at end face.
2. Locate the Anchor Plate on the concrete base and adjust the position according to solution drawing(remove M14 washer,M14 spring washer,and M14 nut if they are connected to embedded bolts now),and then fasten M14 washer, M14 spring washer, and M14 nut with the tightening torque of 60N.m.
3.Take out the Hexagon Bolt Kit with Post B Corrugated Gasket M12x95 and remove its nut, spring washer, one washer, and corrugated gasket. Insert the Post A, B, C in to Anchor Plate according to the Hexagon Bolt Kit with Corrugated Gasket M12x95 drawing and then fix them by two sets of Hexagon Bolt Kit with Corrugated Gasket M12*95. Post C Post A
4.Remove the bolt kits M12*90 from all the Posts and Pre-Assembled Supports and unfold the embedded Supports, fasten them on the Posts by bolt kits M12*90 according to the drawing.

Installation of Rails
1.Please check the length of Beam before place it onto the Pre-Assembled Supports, otherwise extend it with Splice forBeam first. There are 4 self-tapping screws in each side and total 8 self- tapping screws in both sides. We strongly recommend NOT extend the Beams on Preassembled Supports.
2.Before locate the Beams, mark the position of the Beam son the surface of Pre-Assembled Supports with maker pens according to solution drawing for easier installation. Place the Beams on the 55*80 Tube of Pre-Assembled Supports and fix it with C Clamp Kits. Install all the Beams in the same step. The tightening torque will be 20N.m. C Clamp Kit Side Beam(Please arrange 3-4 persons to install when the array is long.)

Installation of Solar Panels
1.Place the panels above the Beam 85, fixing it with Wide End Clamp Kit in the side and Inter Clamp Kit in the middle. Install all the panels in the same steps until complete installation of al panels. Fasten all the bolts with tightening torque of 10N.m.
2.Complete installation, and please inspect and make sure all the bolts are fastened.
Solar Panel Mounting Frames,Solar Panel Mounting Systems,Greenhouse Solar Mounting System,PV Mounting Systems
Hebei Honde Plastic & Metal Co., Ltd. , https://www.foundation-system.com